1 Kanal PoE Injector

PoE Injector 1 Kanal, versorgt jedes PoE-Gerät zuverlässig mit Strom (max 15,4W pro Kanal)
1 Kanal PoE Injector
Abbildung kann abweichen. Beachten Sie bitte die Textbeschreibung und das Datenblatt.
54,34 € *

inkl. MwSt. zzgl. Versandkosten

Sofort versandfertig, Lieferzeit ca. 1-3 Werktage

  • V10808
  • Lupus-Electronics
  • 10808
  • 4260195431799
  • 24 Monate
1 Channel Power over Ethernet injector POE-1HP is a low cost 1-Port High Power midspan... mehr
Produktinformationen "1 Kanal PoE Injector"
PoE Injector 1 Kanal, versorgt jedes PoE-Gerät zuverlässig mit Strom (max 15,4W pro Kanal)

1 Channel Power over Ethernet injector

POE-1HP is a low cost
1-Port High Power midspan injector. It is
functionally compliant to the IEEE802.3af
standards. Cat6 cables into 10/100/1000 Base
T systems, eliminating the ne

1 Channel Power over Ethernet injector

POE-1HP is a low cost
1-Port High Power midspan injector. It is
functionally compliant to the IEEE802.3af
standards. Cat6 cables into 10/100/1000 Base
T systems, eliminating the need for
power management and prioritization.

 

APPLICATIONS

Security Camera with Pan/ Tilt/ Zoom IP Print Servers

FEATURES

Fully Compliant with IEEE802.3af 10/100/1000 base T compatible; Full ProtectionOCP, OVP
Full Power of 15.4W per port Cisco AP1250 Full Power Support; rack mount possible
Cisco: no extern parts required for Legacy devices: VoIP Phones (7910, 7912, 7940, 7960)
Access points (350, 1100, 1200)

SAFETY

Isolation Test Primary to Secondary: 4242VDC for 1min. 10mA, Primary to F.G.: 2121VDC for 1 minute, Output to F.G.: 2121VDC for 1 minute
Insulation Resistance Primary to secondary: >10M OHM 500 VDC, Primary to F.G.: >10M OHM 500 VDC

OUTPUT

DC Output 56V @ 15.4W per port
Regulation Functional requirements of IEEE802.3af

INPUT

AC Input Voltage Range 90 to 264 VAC
Leakage Current 3.5 mA max @ 254 VAC 60 Hz
AC Input Frequency 47-63 Hz
AC Inrush Current 30A(RMS) max. for 115VAC/ 60A(RMS) max. for 230VAC
AC Input Current 2.5A for 90VAC / 1.3A for 240VAC

GENERAL

Effi ciency 75% (typical) at max. load and 120VAC 60Hz
Hold-up Time 16mS min. 120VAC and max. load
Transient O/P Voltage Protection 60V max. at switch on and off at any AC line Phase
Turn-On Delay Time 3 sec max. at max. load, and 120VAC 60Hz, 25Hz
Regulation Functional requirements of IEEE802.3af

EMC

Conducted & radiated Emission EN55022 Class A, FCC Class A with UTP Cabling
EN55022 Class B, FCC Class B with FTP Cabling
Immunity EN50082-1 ESD EN61000-4-2. Level 3
RS EN61000-4-3. Level 2
EFT EN61000-4-4. Level 2
Surge EN61000-4-5. Level 3
CS EN61000-4-6. Level 2
Voltage Dips EN61000-4-11
Harmonic EN61000-3-2 Class A

ENVIRONMENTAL

Temperature Operation 0 to +40°C, Non-operation -25 to +65°C
Humidity Operation 5 to 90%
Weiterführende Links zu "1 Kanal PoE Injector"
Bewertungen lesen, schreiben und diskutieren... mehr
Kundenbewertungen für "1 Kanal PoE Injector"
""
Bewertung schreiben
Bewertungen werden nach Überprüfung freigeschaltet.
Bitte geben Sie die Zeichenfolge in das nachfolgende Textfeld ein.

Die mit einem * markierten Felder sind Pflichtfelder.

Zuletzt angesehen